- #Wf 8955an power converter driver
- #Wf 8955an power converter manual
- #Wf 8955an power converter series
The WF-8900 Series is not weather resistant nor designed for installation in wet locations. The WF-8935AN,WF-8945AN,WF-8955AN is equipped with reverse polarity fuses, Should these fuses "blow" either during the manufacturing process or while connecting the batteries replace with the same type and rating fuse as originally provided with the equipment. Should the fuse "blow" or an open be caused the LED will light up indicating which circuit is open and which fuse needs to be replaced. Each 12VDC circuit of the WFCO Distribution panel is provided with a LED indicator light. Replacing it with either a higher or lower amp fuse could result in the panel not functioning properly. Should one need to be replaced be sure to replace it with the same type and amp rating as originally supplied by the OEM.
Square D: Type HOM or HOMT 12 VDC Fuses Each 12 VDC circuit in the WFCO Distribution panel was designed for a maximum of a 20 amp Little Type 257 automotive style fuse. Branch Circuit Breaker-Listed, rated 120Vac, maximum 20 A Culter Hammer: Type BR and C, or BRD BD and A. Main Circuit Breaker-Listed, rated 120Vac, maximum 30 A Culter-Hammer: Type BR and C. IMPORTANT: When replacing circuit breakers replace with the same type and rating as the original. Use only approved circuit breakers and 12V fuses. Should a breaker become faulty replace with the same type breaker as provided by the OEM. Double breakers may be used for the branch circuits. (see wiring diagram) 1ģ Fuses and breakers: Breakers The WF-8935AN, WF-8945AN,WF-8955AN ULTRA Distribution Panel w/ 35,45,55Amp Power Converter was designed to use a 30 AMP main breaker with branch circuits (Cutler- Hammer and SIEMENS are recommended breakers). Be sure to use appropriate Romex connectors and strain reliefs to secure the wires to the box. Leave the rest of the knockouts in place. Remember to select the proper gauge wire for the load and distance.
The 7/8" holes are for the romex on the 120VAC side and the wires on the 12VDC side. Two sizes have been provided, The 1 1/8" is for the 30 amp power cord. The OEM may wish to pre-wire the box for ease of installation, Select the number of knockouts to be used and remove them. Warning: DO NOT MOUNT THE WF-8935AN,WF-8945AN,WF-8955AN IN A BATTERY OR LP GAS COMPARTMENT. Too much torque or use of a power tool, may result in stripped screws, The output terminals are rated to accept 2 to 14 gage, copper or aluminum wire.
#Wf 8955an power converter driver
Use a slot driver to tighten terminal output serews. When routing around the converter be sure that all openings are protected from debris falling into the WF Metal shavings and debris from the manufacturing process allowed to enter the converter may cause damage (this is a non-warranty item). Caution: Do not mount in an area where the owner may store items as this could effect the efficient operation of the converter. The WF-8935AN,WF-8945AN,WF-8955AN should be mounted a minimum of 1" off the floor (2" to 3"would be perfered). Mount in such a way as to provide adequate ventilation to the converter ON ALL SIDES. The hole should be framed so that the box can be secured tightly.
#Wf 8955an power converter manual
Sales (574) Warranty Service (877)Ģ Installation/Operator's Manual For use with WFCO ULTRA Models: WF-8935AN,WF-8945AN,WF-8955AN Mounting: Select the mounting location near the shore power inlet and batteries and cut a rough opening 1/8" wider than the box to allow the Distribution panel to slide in easily. 1 Installation/Operators Manual For use with WFCO ULTRA Distribution Panels Models WF-8935AN W/PLASTIC, WF-8945AN W/PLASTIC, WF-8955AN W/PLASTIC Distributed in the US by CHENG USA, Inc.
0 kommentar(er)
